108,5 dB SPL 1W / 1m average sensitivity 1 inch exit throat34,4 mm (1 1/3 inch) voice coil diameterPolyethylene Diaphragm60W Program Power HandlingCompact Lightweight NeodymiumStructure Proprietary Phase Plug design
The ND1020 1-inch exit high frequency compression driver has been designed for use in situations where the highest possible sound quality is required.Polyethylene Naphthalate (PEN) has been used for the diaphragm assembly, giving to ND1020 a superior diaphragm dimensional stability compared to conventional Mylar film (160°C as a thermal rating compared to 105°C for PET) and maintaining a constant performance during its whole working life. PEN film, with its very high value of elasticity modulus (6000MPa compared to 4000MPa for PET and 2800MPa for polyimide film), is capable of a superior transient and intermodulation distortion response. The flat punched suspension shape has been designed to maintain low stiffness for superior low mid band distortion and response.An edge-wound copper clad aluminum voice coil wound on treated Nomex completes the diaphragm assembly. Nomex shows a 20% higher value of tensile elongation at 200°C than the value at room temperature, (in comparison, Kapton tensile elongation is 30% lower at 200°C than the value at room temperature). Hence, Nomex is capable of keeping energy transfer from the voice coil to the dome under control, especially when the voice coil reaches high temperatures. As a plus, treated Nomex former voice coil can work well even in high moisture content environments, thanks to its very low porosity.The ND1020 is equipped with unique Phase Plug architecture, designed to give smooth coherent wave front at the horn entrance over the whole working frequency range, as well as high level manufacturing consistency. The phase plug design shows short openings and high flare rate value, assuring low distortion and demonstrates remarkable improvements in mid-high frequency reproduction.By carefully using elementary pieces of neodymium magnets, Eighteen Sound engineers have developed a powerful neodymium magnet assembly capable of reaching 18KGauss in the gap within a compact and lightweight structure.
Thiele Small Parameters
Mounting information
The ND1020 1-inch exit high frequency compression driver has been designed for use in situations where the highest possible sound quality is required.Polyethylene Naphthalate (PEN) has been used for the diaphragm assembly, giving to ND1020 a superior diaphragm dimensional stability compared to conventional Mylar film (160°C as a thermal rating compared to 105°C for PET) and maintaining a constant performance during its whole working life. PEN film, with its very high value of elasticity modulus (6000MPa compared to 4000MPa for PET and 2800MPa for polyimide film), is capable of a superior transient and intermodulation distortion response. The flat punched suspension shape has been designed to maintain low stiffness for superior low mid band distortion and response.An edge-wound copper clad aluminum voice coil wound on treated Nomex completes the diaphragm assembly. Nomex shows a 20% higher value of tensile elongation at 200°C than the value at room temperature, (in comparison, Kapton tensile elongation is 30% lower at 200°C than the value at room temperature). Hence, Nomex is capable of keeping energy transfer from the voice coil to the dome under control, especially when the voice coil reaches high temperatures. As a plus, treated Nomex former voice coil can work well even in high moisture content environments, thanks to its very low porosity.The ND1020 is equipped with unique Phase Plug architecture, designed to give smooth coherent wave front at the horn entrance over the whole working frequency range, as well as high level manufacturing consistency. The phase plug design shows short openings and high flare rate value, assuring low distortion and demonstrates remarkable improvements in mid-high frequency reproduction.By carefully using elementary pieces of neodymium magnets, Eighteen Sound engineers have developed a powerful neodymium magnet assembly capable of reaching 18KGauss in the gap within a compact and lightweight structure.
Throat Diameter | 25,4 mm (1 in) |
Rated Impedance | 8 Ohm |
DC Resistance | 5,8 Ohm |
Minimum Impedance | 6,5 Ohm at 5000Hz |
Le (at 1kHz) | 54 µH |
AES Power | 30 W above 2 kHz |
Program Power | 60 W above 2 kHz |
Sensitivity | 108,5 dB |
Frequency Range | 1600Hz ÷ 20kHz |
Recomm. Xover Frequency | 1600 Hz 12dB/oct slope |
Minimum Impedance | 6,5 Ohm at 5000Hz |
Diaphragm Material | Treated polyethylene |
Voice Coil Diameter | 34,4 mm (1 1/3 in) |
Voice Coil Winding Material | Edge-wound aluminum |
Magnet Material | Neodymium |
Flux Density | 1,8 T |
BL Factor | 6 N/A |
Polarity | Positive voltage on red terminal gives positive pressure in the throat |
Overall diameter | 85 mm (3,3 in) |
N. of mounting holes and bolt | 2 M5 holes on Ø 76 mm (3 in) |
Bolt circle diameter | 58 mm (2,3 in) |
Total depth | 40,5 mm (1,6 in) |
Net weight | 0,7 Kg (1,54 lb) |
Shipping weight | 0,75 Kg (1,65 lb) |
CardBoard Packaging dimensions | 97x97x58 mm (3,8x3,8x2,3 in) |
- Außendurchmesser
- 85 mm (3.35 in)
- Einbautiefe
- 40 mm (1.57 in)
- Empfindlichkeit
- 108.5 dB
- Netto Gewicht
- 0.7 kg
- Wicklung besteht aus
- Aluminum
- Schwingspulendurchmesser
- 34 mm (1.34 in)
- MInimale Impedanz
- 6.5 Ω
- Nominale Belastbarkeit
- 30 W
- Versandkarton
- 97x97x58 mm (3.82x3.82x2.28 in)
- Frequenzbereich
- 1.6 - 20.0 kHz
- Nominale Impedanz
- 8 Ω
- Versandgewicht
- 0.75 kg ( lb)
- Magnet
- Neodymium
- Recommended Crossover
- 1.6 kHz
- Throat Diameter
- 25 mm (1.0 in)
- Dauerbelastbarkeit
- 60 W
- Diaphragm Material
- Treated polyethylene
Wir informieren Sie gern darüber, falls der Preis dieses Artikels Ihrem Wunschpreis entspricht.
Artikel bewerten
Es liegen keine Bewertungen zu diesem Artikel vor.