Eighteensound 18NLW9000 Extended LF Neodymium Transducer Lautsprecher

Artikelnummer: ES18NLW9000

Extended LF Neodymium Transducer

Lieferzeit ca. 2 - 4 Werktage

Versandkostenfreie Lieferung voraussichtlich zwischen Saturday, 30.03 und Monday, 01.04 nach Deutschland

Mengenstaffelpreise
Von 2 Stück 672,08 €
Von 4 Stück 651,51 €
Von 8 Stück 644,65 €
Von 14 Stück 630,94 €
? Warenkorb in PayPal anzeigen
  • 97 dB SPL 1W / 1m average sensitivity
  • 135 mm (5.3 in) ISV aluminum voice coil
  • 3600 W program power handling
  • Carbon fiber reinforced cone
  • Double Silicon Spider (DSS) technology
  • Low noise forced ventilation design reduces power compression
  • High grade neodymium magnet assembly
  • Weather protected cone and plates for outdoor usage
  • Suitable for vented and bandpass high SPL subwoofer systems

The 18NLW9000 is an 18 inch neodymium high performance subwoofer. The loudspeaker has been directly derived from our flagship 18NLW9600, and has been optimized for vented and bandpass subwoofer cabinet designs. For optimum results recommended amplifier should be able to deliver 3600 Watt program power without clipping. Eighteen Sound engineers have obtained the best possible results with today's available materials in terms of clean and undistorted LF reproduction at a ultra high SPL, with the lowest possible power compression figure. The transducer design features include a large displacement suspension system specifically designed for matching the carbon fiber reinforced, straight ribbed cone. Thanks to the Double Silicon Spider (DSS) technology, the 18NLW9000 is able to control the moving mass with high linearity, showing an exceptional stability of mechanical parameter values in the long term. Bl force factor, as well as all other electro-dynamic parameters, are linear within the working range. This, together with the exceptional high excursion behavior - 70mm before damage, ±14mm linear Xmax - makes the 18NLW9000 an extremely low distortion, highly dynamic transducer. The state-of-the-art 5,3" inside outside ISV (Interleaved Sandwich Voice Coil) aluminum voice coil enables the 18NLW9000 to handle 3600W program power value. The 18NLW9000 has been developed after intense FEA and fluidodynamics simulation and testing, focusing on dissipating the heat generated by the powerful voice coil. Special attention was given to the optimization of air flow into the gap without introducing audible noise. A low-density material air diffractor placed into the heatsink acts as a cooling system, increasing the power handling capability and lowering the power compression figure. 18NLW9000 is able to perform properly under inclement weather conditions: the exclusive cone treatment improves pulp strength and gives water repellent properties to both sides of the cone. A special coating applied to both the top and back plates makes the transducer far more resistant to the corrosive effects of salts and oxidization.

Nominal Diameter 462 mm (18 in)
Rated Impedance 8 Ohm
AES Power 1800W
Program Power 3600W
Peak Power 10000W
Sensitivity 97 dB
Frequency Range 32 - 2500 Hz
Power Compression @-10dB 0,7 dB
Power Compression @-3dB 1,2 dB
Power Compression @Full Power 2,2 dB
Max Recomm. Frequency 150 Hz
Recomm. Enclosure Volume 120 ÷ 350 lt. (4.2 ÷ 12.4 cuft)
Minimum Impedance 6,7 Ohm at 25°C
Max Peak To Peak Excursion 70 mm (2,75 in)
Voice Coil Diameter 135 mm (5,3 in)
Voice Coil Height 32 mm (1.26 in)
Voice Coil Technology 2 layers copper clad aluminum wire
Gap Depth 12 mm (0.47 in)
Suspension Triple Roll, Polycotton
Cone Straight ribbed, carbon fiber reinforced cellulose
Thiele Small Parameters
Fs 34 Hz
Re 5,5 Ohm
Sd 0,1225 sq.mt. (190 sq.in.)
Qms 7
Qes 0,32
Qts 0,31
Vas 206 lt. (7.3 cuft)
Mms 218 gr. (0,48 lb)
BL 26.8 Tm
Linear Mathematical Xmax ±14 mm (±0,55 in)
Le (1kHz) 1,90 mH
Ref. Efficiency 1W@1m (half space) 96,1 dB
Mounting information
Overall diameter 462 mm (18,18 in)
N. of mounting holes and bolt 8
Mounting holes diameter 8,5 mm (0,33 in)
Bolt circle diameter 440mm (17,32 in)
Front mount baffle cutout ø 416 mm (16,38 in)
Rear mount baffle cutout ø 422 mm (16,61 in)
Total depth 237,5 mm (9,3 in)
Flange and gasket thickness 26 mm (1,02 in)
Net weight 12,5 kg (27,6 lb)
Shipping weight 13,8 kg (30,42 lb)
CardBoard packaging dimensions
 482x482x257 mm (19x19 x10,1 in)
Qts
0.31
Lochkreisdurchmesser
440 mm (17.32 in)
EBP
106 Hz
Resonanz Frequenz
34 Hz
Xmax
14.0 mm
Nominale Impedanz
8 Ω
Frequenzbereich
32 - 2500 Hz
Schallwandausschnitt
422.0 mm (16.61 in)
Qms
7.0
Sd
1222.0 cm2 (189.41 in2)
Einbautiefe
237 mm (9.35 in)
Schwingspulendurchmesser
135 mm (5.31 in)
Le
1.9 mH
Nominale Belastbarkeit
1800 W
BL
28.0 Txm
MInimale Impedanz
6.7 Ω
Qes
0.32
Dauerbelastbarkeit
3600 W
Außendurchmesser
462 mm (18.19 in)
Tuning Frequenz
36 Hz
Mms
218.0 g
Netto Gewicht
12.5 kg
Versandgewicht
14.0 kg (30.86 lb)
Re
5.5 Ω
Recommended Enclosure
200.0 dm3 (7.06 ft3)
Vas
206.0
Flange and Gasket Thickness
26 mm (1.02 in)
Empfindlichkeit
97.0 dB
Versandkarton
482 x 482 x 257 mm (18.98x18.98x10.12 in)

Wir informieren Sie gern darüber, falls der Preis dieses Artikels Ihrem Wunschpreis entspricht.

Es liegen keine Bewertungen zu diesem Artikel vor.