Dieser Online-Shop verwendet Cookies für ein optimales Einkaufserlebnis. Dabei werden beispielsweise die Session-Informationen oder die Spracheinstellung auf Ihrem Rechner gespeichert. Ohne Cookies ist der Funktionsumfang des Online-Shops eingeschränkt. Sind Sie damit nicht einverstanden, klicken Sie bitte hier.

Eighteensound 18W1300 Low Frequency Transducer Lautsprecher

Low Frequency Transducer

ArtNr.: ES18W1300
305,00 *
Gewicht:: 15 kg
Sofort lieferbar.
99,5 dB SPL 1W / 1m average sensitivity100 mm (4 in) Interleaved Sandwich Voice coil (ISV)850 W AES power handlingWeather protected cone and plates for outdoor usageDouble Silicon Spider (DSS) for improved excursion control and linearityDouble Demodulating Rings (DDR) for lower distortion and improved heat dissipationImproved heat dissipation via unique basket design
The 18W1300 is a low frequency loudspeaker which sets a new industry standard in 18" (460 mm) high output transducers. It represents a further development of the Eighteen Sound 18LW1400 but with a lighter mass and increased sensitivity.The 18W1300 can be used as a low bass or subwoofer component, in either a reflex, bandpass or horn loaded configuration, in high power fixed or touring loudspeaker systems. It provides clean, linear, undistorted low frequency reproduction at very high power levels. In its reflex configuration, it can also be used for bass musicalinstrument applications.The high excursion capabilities of the surround and suspension system, in conjunction with the Double Silicon Spider (DSS), enable the 18W1300 to achieve high levels of linear travel while maintaining full control over the moving mass.The carbon fiber reinforced curvilinear ribbed cone assures smooth response and exceptional strength with maximum reliability under high mechanical stress.The state-of-the-art voice coil employs our own Interleaved Sandwich Voice coil (ISV) technology, in which a high strength fiberglas former carries windings on both the outer and inner surfaces. This results in a balanced coil with a uniform distribution of mass and motive energy, creating an extremely linear motor assembly. The already low distortion and unmistakable sound quality of this loudspeaker is improved by Double Demodulating Rings (DDR), designed to dramatically reduce the intermodulationand harmonic distortion while improving the transient response.Excellent heat dissipation has been achieved by incorporating air channels between the basket and the magnetic top plate.Maximum flux concentration and force factor in the gap is assured by the unique shape and design of the top and back plates, which have been researched and designed using our in-house magnetic flux FEA CAD resource.Due to the increasing use of high power audio systems at outdoor events or in marine environments, the 18W1300 has been designed to perform properly under inclement weather conditions. This has been achieved using of an exclusive cone treatment which improves pulp strength and gives water repellent properties to both sides ofthe cone. In addition, a special treatment is applied to the top and back plates which is far more resistant to the corrosive effects of salts and oxidization than any other treatment in use.

Nominal Diameter 460 mm (18 in)
Rated Impedance 8 Ohm
AES Power 850 W
Program Power 1200 W
Peak Power 6000 W
Sensitivity 99,5 dB
Frequency Range 38 - 3300 Hz
Power Compression @-10dB 0,7 dB
Power Compression @-3dB 2,1 dB
Power Compression @Full Power 3,2 db
Max Recomm. Frequency 500 Hz
Recomm. Enclosure Volume 150 ÷ 350 lt. (5,3 ÷ 12,36 cuft)
Max Peak To Peak Excursion 50 mm (1,97 in)
Voice Coil Diameter 100 mm (4 in)
Voice Coil Winding Material aluminum
Suspension Triple roll, polycotton
Cone Curvilinear ribbed, Paper
Thiele Small Parameters
Fs 35 Hz
Re 5 Ohm
Sd 0,1225 sq. mt. (189,88 sq. in.)
Qms 5
Qes 0,35
Qts 0,33
Vas 336 lt. (11,87 cuft)
Mms 129 gr. (0,28 lb)
BL 20,4 Tm
Linear Mathematical Xmax ± 8,5 mm (± 0,33 in)
Le (1kHz) 1,48 mH
Ref. Efficiency 1W@1m (half space) 98,2 dB
Mounting information
Overall diameter 462 mm (18,18 in)
N. of mounting holes and bolt 8
Mounting holes diameter 8,5 mm (0,33 in)
Bolt circle diameter 438-440 mm (17,24-17,32 in)
Front mount baffle cutout ø 416 mm (16,38 in)
Rear mount baffle cutout ø 422 mm (16,61 in)
Total depth 211,9 mm (8,34 in)
Flange and gasket thickness 26 mm (1,02 in)
Flange and gasket thickness 26 mm (1,02 in)
Net weight 13 kg (28,7 lb)
Shipping weight 14,4 kg (32 lb)
CardBoard Packaging dimensions 482 x 482 x 257 mm (18,98 x 18,98 x 10,12 in)
lieferbar
sofort lieferbar
Hersteller
Eigteensound
Preis
300 - 400 EUR
Low Frequency Transducer
Low Frequency Transducer

Gerne informieren wir Sie unverbindlich darüber, falls sich der Preis dieses Artikels ändert bzw. Ihrem Wunschpreis entspricht.

Prüfcode

Es liegen keine Kommentare zu diesem Artikel vor.
Statt 45,60 € 29,99 € *
auf Lager
Statt 39,20 € 29,40 € *
auf Lager
Statt 45,60 € 34,79 € *
auf Lager
Statt 34,00 € 24,80 € *
auf Lager
Statt 45,60 € 34,89 € *
auf Lager
Statt 26,80 € 19,75 € *
auf Lager
Statt 7,80 € 6,00 € *
auf Lager
* inkl. MwSt., zzgl. Versandkosten